- FORESEE GARAGE DOOR OPENER MANUAL MANUAL
- FORESEE GARAGE DOOR OPENER MANUAL FULL
- FORESEE GARAGE DOOR OPENER MANUAL CODE
One-Piece Doors 5 A TT ACHING DOOR BRA CKET TO DOOR NOTE: Center bracket on door as high as possible, preferably top edge. (Follow these same steps to change Intellicode® 1 back to Intellicode® 2. The default Intellicode ® 2 setting must be changed to Intellicode® 1. INTELLICODE 1 REMOTES Remotes provided with this unit can operate other (Intellicode® 1) models of Genie® garage door openers. NOTE: When the remote is pressed the round LED will flash blue but will not activate the door opener. NOTE: The garage door opener will operate normally using the Wall Console. Optional Programming 4 CLEARING MEMOR Y FOR REMOTES If the memory has been cleared, the Remote will not activate the door opener. Programming Locate Y our Opener’ s Programming Buttons and LED Synchronizing Keypad to Opener 1. Optional Programming 4 Setting Up a PIN 1. Each Remote can be programmed for three door openers. T o program the same Remote for other garage door openers, repeat the steps above using one of the other two Remote buttons. Repeat as necessar y for additional Remotes. This Remote is preset for use with the Intellicode 2 Access Security System. Required Programming 3 REMOTES / New Intellicode 2 Openers NOTE: The following instructions are for the remote control transmitters (“Remotes”) provided with this opener.
FORESEE GARAGE DOOR OPENER MANUAL FULL
The door MUST complete a full cyc le from open to close and c lose to open before it is fully set. Required Programming 3 Force and Speed Control These controls are factory programmed and automa tically set themselves when you use the Wall Console to open and c lose the garage door for the rst time.
5A S/N:10XXXX XXXXXXX STB BWC IWC NOT USED NOT USED N. R quired Pr ramming Required Programming 3 MODEL AC SR3 THE GENIE COMPANY FCC ID: B8Q AC SR3 Residential Door Operator IC: 2 33A-CS 1D 120V. PROGRAM SET PROGRAM – + 5 Press and release the Program Set button (both LEDs flash blue and go off). Opening Garage Door (Up Limits) NOTE: Beginning with garage door c losed is recommended but not necessary. Required Programming 3 The DOWN (closed) limit is programmed. If not illuminated, check for correct wiring or the Sure-Lock switch may be activated. NOTE: Before setting limits confirm wall console red indicator light (or backlight) is ON. TRA VEL LIMITS NOTE: If shuttle/bullet has NOT been enga ged to carriage, do so now. INTRODUCTION Now that your Genie gara ge door opener is installed, you will want to program the opener so that the door opens and closes properly and all remote devices operate correctly. Required Programming 3 NOTE: Before you begin programming, check to make sure there are no objects in the garage door opening.
FORESEE GARAGE DOOR OPENER MANUAL CODE
LED indicator lights on the powerhead and on the STBs provide a self-diagnostic code if an operational problem exists. The door stops and reverses to the full open position if anything passes through the beam. SafetyInformation 1 OVERVIEW OF PO TENTIAL HAZARDS READ THIS SAFETY INFORMA TION CONVENTIONS USED IN THESE INSTRUCTIONS Garage doors are large, heavy objects tha t move with the help of springs under high tension and electric motors.įeatures 2 SAFETY FEA TURES Safe-T -Beam ® (STB) Non-Contact Reversing System Puts an invisible beam across the door opening.
FORESEE GARAGE DOOR OPENER MANUAL MANUAL
For Answers and Assistance: 1.800.354.3643 or visit SAVE THIS MANUAL FOR FUTURE REFERENCE INST ALLER: LEAVE THIS MANUAL WITH HOMEOWNER GARAGE DOOR OPENER MODELS P owerMax ® 120.
0 kommentar(er)
